Converter Type

SOPTO N x E1 to Ethernet converters’ maximum transmission capacity is up to 16E1. It uses reverse multiplexing technology to transmit 10/100BaseT data with bonding multi E1 channels, when used in 10/100Mbps half/full duplex mode.

TDMoIP is a new technology, which is developed based on the WDM and IP protocol. TDMOIP can transmit E1 signal in IP network transparently. TDMoIP is mainly used to transmit voice signal over IP network.

V.35 to ETH converter, device for converting from V.35 to 10Base-T, is a kind of high performance, self-study and long-distance ETH bridges. It can realize the convert between the V.35 interface and Ethernet interface.

Multi-port UTP Media converter enables the connection of several end Ethernet devices using Twisted Pair cable. An additional 100Base-FX Port can be used for the connection to central switch or hub. The use of the Multi-port UTP converter in the end devic

SOPTO Industrial Media Converters are compact and robust devices. They are designed to convert and transmit Ethernet, Serial or video signals over fibre optic networks by transparently converting digital electric Ethernet signals into optical signals.

SOPTO’s Managed Media Converters extended copper to fiber, multimode to multimode and multi-mode to single mode fiber with extensive security, network integration and ease of use features that are not available in similar products by other manufacturers.

SOPTO remote fiber optic Ethernet media converter can be used as a standalone unit or a slide-in module to a 19-inch converter rack or a central wiring closet. This media converter is designed to convert data signals between 10/100 Base-Tx and 100 Base-Fx

Media converter card is fast Ethernet media converter. It can be inserted into rack-mount chassis or inserted into standalone shell. It is primarily designed for large, higher speed/ bandwidth demanding workgroups that require expansion of the Ethernet ne

E1 to Fiber Converter with E1 to Ethernet interface, its interface up to 8E1 or T1 circuit and delivers these clear trunks transparently across a fiber link, its transmission distance up to 2.5 Km at 62.5/125 um fiber, 850nm wavelength up to 12 Km at 62.5

The E1 to N x Ethernet converter also as FE1 to Ethernet Bridge, it is mainly accomplished the converting between the Nx100M Ethernet ports and the E1 port. E1 interfaces conforming to ITU-T G.703 and G.704 proposals are provided at the end of WAN, suppor

E1 to RS232/RS422/RS485 Converter is conversion equipment between the standard E1 interface and standard RS232/RS422/RS485 interface with ITU-T G.703. It provides safe and seamless connection of communication between different devices with different inter

SOPTO E1 to V.35 converter and E1 to V.24 converter use one E1/G.703 to convert to V.35. It can convert successive N*64K (N=1--32) data stream into PCM signal of E1. The data rate is up to 2048Kbps.

The Media Converter complies with IEEE 802.3z, IEEE 802.3AB Standards. It is designed to convert data signal between 10/100Base-T and 100Base-FX Fast Ethernet. It supports 10/100Base-T and 100Base-FX applications.

The Media Converter complies with IEEE 802.3z, IEEE 802.3AB Standards. It is designed to convert data signal between 10/100/1000Base-T and 1000Base-LX Gigabit Ethernet. It supports 10/100/1000Base-T and 1000Base-LX applications.

SOPTO 10 Gigabit Ethernet to Fiber Converters provide an economical path to extend the distance of an existing 10GbE link. Network Administrators can “see-everything” with SOPTO’s advanced features such as Smart Link Pass-Through, Fiber Fault Alert, a bui

SOPTO SFP fiber optic media converter is fully compliant with IEEE802.3z & 802.3ab standards. It can be installed into a Standard Converter Chassis. The installation & operation procedures are simple & straightforward. Operation status can be locally moni

The core strength of media converter is the ability to convert any signaling rate, from 155Mbps to 1.25Gbps, being an Universal Fiber Converter - ideal for any communication standard like: Fast and Gigabit Ethernet, STM-1 and STM-4, OC-1, OC-3, OC-12 and

Connect Gigabit-speed fiber optic to a 10-/100-/1000-Mbps copper UTP segment while also powering 802.3af devices at the end of the CAT5 run.

SOPTO PoE PD media converter is used to bridge long-distance fast Ethernet fiber optic segments with Ethernet or fast Ethernet copper cabling---All without the need for a local power supply.

This Single Mode to Multimode Fiber Media Converter provides transparent conversion between single mode and multimode fiber networks, providing a cost-effective way to utilize two different types of fiber cabling.