Connecting the world with professional
Fiber Optic Solutions

Product
 
 
email to us



 
Related Products
 
Product Category
 
 
Related Products

SPT-P133G-20D 3.072Gbps SFP Optical Transceiver, 20km Reach

1550nm 1G fiber optic transceiver

SPT-P133G-20D

3.072Gbps SFP Optical Transceiver, 20km Reach

Features

  • Operating data rate up to 3.072Gbps
  • CPRI/OBSAI Compatible Optical Interface
  • Compliant with SFP MSA and SFF-8472 with duplex LC receptacle
  • 1310nmDFB-LD Transmitter and PIN photo detector
  • Distance up to 20km with SMF
  • Digital Diagnostic Monitoring: Internal Calibration or External Calibration
  • Compatible with RoHS
  • +3.3V single power supply
  • Operating case temperature:
    Standard: 0 to 70 °
    Industrial: -40 to +85°C

Applications

  • Radio Base Station
  • OBSAI rates 3.072Gb/s, 1.536Gb/s, 0.768Gb/s
  • CPRI rates 3.072Gb/s, 2.4576Gb/s, 1.2288Gb/s, and 0.6144Gb/s


Description
The SFP transceivers are high performance, cost effective modules supporting dual data-rate up to 3.072Gbps and 20km transmission distance with SMF.
The transceiver consists of three sections: a DFB laser transmitter, a PIN photodiode integrated with a trans-impedance preamplifier (TIA) and MCU control unit. All modules satisfy class I laser safety requirements. The transceivers are compatible with SFP Multi-Source Agreement (MSA) and SFF-8472. For further information, please refer to SFP MSA.
 
Absolute Maximum Ratings

Parameter

Symbol

Min

Max

Unit

Supply Voltage

Vcc

0

4.0

V

Storage Temperature

Ts

-40

+85

°C

Operating Humidity

-

5

85

%

Recommended Operating Conditions

Parameter

Symbol

Min

Typical

Max

Unit

Operating Case Temperature

Standard

Tc

0

 

+70

°C

Industrial

-40

+85

Power Supply Voltage

Vcc

3.13

3.3

3.47

V

Power Supply Current

Icc

 

 

300

mA

Data Rate

 

-

3.072

-

Gbps

Optical and Electrical Characteristics

Parameter

Symbol

Min

Typical

Max

Unit

Notes

Transmitter

Centre Wavelength

λc

1260

1310

1360

nm

 

Spectral Width(RMS)

σ

 

 

1

nm

 

Side Mode Suppression Ratio

SMSR

30

 

 

dB

 

Average Output Power

Pout

-5

 

0

dBm

1

Extinction Ratio

ER

8.2

 

12

dB

 

Optical Rise/Fall Time(20%~80%)

tr/tf

 

 

0.16

ns

 

Data Input Swing Differential

VIN

400

 

1800

mV

2

Input Differential Impedance

ZIN

90

100

110

Ω

 

TX Disable

Disable

 

2.0

 

Vcc

V

 

Enable

 

0

 

0.8

V

 

TX Fault

Fault

 

2.0

 

Vcc

V

 

Normal

 

0

 

0.8

V

 

Receiver

Centre Wavelength

λc

1260

 

1580

nm

 

Receiver Sensitivity

 

 

 

-18

dBm

3

Receiver Overload

 

-3

 

 

dBm

3

LOS De-Assert

LOSD

 

 

-20

dBm

 

LOS Assert

LOSA

-30

 

 

dBm

 

LOS Hysteresis

 

1

2

4

dB

 

Data Output Swing Differential

Vout

370

 

1800

mV

4

LOS

High

2.0

 

Vcc

V

 

Low

 

 

0.8

V

 

Note:
1. The optical power is launched into SMF.
2. Internally AC-coupled and terminated.
3. Measured with a PRBS 2 -1 test pattern @3072Mbps, BER ≤1×10
4. Internally AC-coupled.


Timing and Electrical

Parameter

Symbol

Min

Typical

Max

Unit

Tx Disable Negate Time

t_on

 

 

1

ms

Tx Disable Assert Time

t_off

 

 

10

µs

Time To Initialize,Including Reset of Tx Fault

t_init

 

 

300

ms

Tx Fault Assert Time

t_fault

 

 

100

µs

Tx Disable To Reset

t_reset

10

 

 

µs

LOS Assert Time

t_loss_on

 

 

100

µs

LOS De-assert Time

t_loss_off

 

 

100

µs

Serial ID Clock Rate

f_serial_clock

 

 

400

KHz

MOD_DEF(0:2)-High

VH

2

 

Vcc

V

MOD_DEF(0:2)-Low

VL

 

 

0.8

V

Diagnostics

Parameter

Range

Unit

Accuracy

Calibration

Temperature

0to+70

°C

±3°C

Internal/External

-40 to +85

Voltage

3.0 to 3.6

V

±3%

Internal/External

Bias Current

0 to 100

mA

±10%

Internal/External

TX Power

-5 to 0

dBm

±3dB

Internal/External

RX Power

-20 to -3

dBm

±3dB

Internal/External

Digital Diagnostic Map
The transceivers provide serial ID memory contents and diagnostic information about the present operating conditions by the 2-wire serial interface (SCL, SDA).
The diagnostic information with internal calibration or external calibration all are implemented, including received power monitoring, transmitted power monitoring, bias current monitoring, supply voltage monitoring and temperature monitoring.
The digital diagnostic memory map specific data field defines as following.

3G SFP for 20km reach

Pin Definitions

3G SFP

 Pin Descriptions

Pin

Signal Name

Description

Plug Seq.

Notes

1

VEET

Transmitter Ground

1

 

2

TX FAULT

Transmitter Fault Indication

3

Note1

3

TX DISABLE

Transmitter Disable

3

Note2

4

MOD_DEF(2)

SDA Serial Data Signal

3

Note3

5

MOD_DEF(1)

SCL Serial Clock Signal

3

Note3

6

MOD_DEF(0)

TTL Low

3

Note3

7

Rate Select

Not Connected

3

 

8

LOS

Loss of Signal

3

Note4

9

VEER

Receiver Ground

1

 

10

VEER

Receiver Ground

1

 

11

VEER

Receiver Ground

1

 

12

RD-

Inv. Received Data Out

3

Note5

13

RD+

Received Data Out

3

Note5

14

VEER

Receiver Ground

1

 

15

VCCR

Receiver Power Supply

2

 

16

VCCT

Transmitter Power Supply

2

 

17

VEET

Transmitter Ground

1

 

18

TD+

Transmit Data In

3

Note6

19

TD-

Inv. Transmit DataIn

3

Note6

20

VEET

Transmitter Ground

1

 

Notes:
Plug Seq.: Pin engagement sequence during hot plugging.
1) TX Fault is an open collector output, which should be pulled up with a 4.7k~10kΩ resistor on the host board to a voltage between 2.0V and Vcc+0.3V. Logic 0 indicates normal operation; Logic 1 indicates a laser fault of some kind. In the low state, the output will be pulled to less than 0.8V.
2) TX Disable is an input that is used to shut down the transmitter optical output. It is pulled up within the module with a 4.7k~10kΩ resistor. Its states are:
  Low (0 to 0.8V): Transmitter on
  (>0.8V, < 2.0V): Undefined
  High (2.0 to 3.465V): Transmitter Disabled
  Open: Transmitter Disabled
3) Mod-Def. 0, 1, 2. These are the module definition pins. They should be pulled up with a 4.7k~10kΩ resistor on the host board.
  The pull-up voltage shall be VccT or VccR.
  Mod-Def. 0 is grounded by the module to indicate that the module is present
  Mod-Def. 1 is the clock line of two wire serial interface for serial ID
  Mod-Def. 2 is the data line of two wire serial interface for serial ID
4) LOS is an open collector output, which should be pulled up with a 4.7k~10kΩ resistor. Pull up voltage between 2.0V and Vcc+0.3V. Logic 1 indicates loss of signal; Logic 0 indicates normal operation. In the low state, the output will be pulled to less than 0.8V.
5) RD-/+: These are the differential receiver outputs. They are internally AC-coupled 100 differential lines which should be terminated with 100Ω (differential) at the user SERDES.
6) TD-/+: These are the differential transmitter inputs. They are internally AC-coupled, differential lines with 100Ω differential termination inside the module.

Recommended Interface Circuit

3G SFP

Mechanical Dimensions

3G SFP transceiver for 20km reach

Ordering Information

Part Number

Product Description

SPT-P133G-20D

1310nm, 3.072Gbps, 20km, 0ºC~+70ºC, DDM

SPT-P133G-20TD

1310nm, 3.072Gbps, 20km, -40ºC~+85ºC, DDM

 

E-mail:sales@sopto.com

Web:http://www.sopto.com