Connecting the world with professional
Fiber Optic Solutions

Product
 
 
email to us



 
Related Products
 
Product Category
 
 
Related Products

10G 1330/1270nm 40km BIDI SFP+ Transceiver SPT-PB3327TG-L40D

1550nm 1G fiber optic transceiver

PRODUCT FEATURES

  • Up to 10.7Gbps Data Links
  • Up to 40km transmission on SMF
  • Power dissipation<1.5W
  • 1330nm DFB laser and PIN receiver
  • EEPROM with Serial ID Functionality
  • Compliant with FC_PI_4 REV 7.0
  • Single Mode LC Receptacle Bi-directional Transceiver
  • 2-wire interface with integrated Digital Diagnostic monitoring
  • Compliant with SFP+ MSA with duplex LC connector
  • Single + 3.3V Power Supply
  • Case operating temperature: -5ºC~+70ºC

APPLICATIONS

  • 10GBASE-BX at 10.3125 Gb/s
  • 10GBASE-BX at 9.953 Gb/s
  • 1000 Base-LX Ethernet
  • 8XFC at 8.5Gbps
  • 4XFC at 4.25Gpbs
  • 2XFC at 2.125Gpbs
  • 1xFC at 1.0625Gbps

STANDARD

  • Compliant with SFF-8472 SFP+ MSA.
  • Compliant with FC_PI_4 REV 7.0.
  • Compliant to SFP+ SFF-8431 and SFF-8432.
  • Compliant to 802.3ae 10GBASE-LR.
  • RoHS Compliant.

PRODUCT DESCRIPTION

SPT-PB3327TG-L40D is hot pluggable 3.3V Small-Form-Factor transceiver module. It designed expressly for high-speed communication applications that require rates up to 10.7Gb/s,it designed to be compliant with SFF-8472 SFP+ MSA. The module data link up to 40km in 9/125um single mode fiber. The optical output can be disabled by a LVTTL logic high-level input of Tx Disable. Tx Fault is provided to indicate that degradation of the laser. Loss of signal (LOS) output is provided to indicate the loss of an input optical signal of receiver or the link status with partner.

Ⅰ. Absolute Maximum Ratings

 

Parameter

Symbol

Min.

Typ.

Max.

Unit

Note

Storage Temperature

Ts

-40

-

85

ºC

 

Storage Ambient Humidity

HA

5

-

95

%

 

Operating Relative Humidity

RH

-

-

85

%

 

Power Supply Voltage

VCC

-0.3

-

4

V

 

Signal Input Voltage

 

Vcc-0.3

-

Vcc+0.3

V

 

 

Ⅱ. Recommended Operating Conditions

 

Parameter

Symbol

Min.

Typ.

Max.

Unit

Note

Case Operating Temperature

Tcase

-5

-

70

ºC

Without air flow

Power Supply Voltage

VCC

3.14

3.3

3.47

V

 

Power Supply Current

ICC

-

300

450

mA

 

Data Rate

BR

 

10.3125

 

Gbps

 

Transmission Distance

TD

 

 

40

km

Note (1)

Coupled fiber

Single mode fiber

ITU-T G.652

 

Note: Measured with SMF

Ⅲ. Optical Characteristics

 

Parameter

Symbol

Min.

Typ.

Max.

Unit

Note

Transmitter

Average Launched Power

PO

-1

-

+4

dBm

 

Average Launched Power(Laser Off)

POUT-OFF

-

-

-40

dBm

Note (1)

Center Wavelength Range

λC

1320

1330

1340

nm

 

Side mode suppression ratio

SMSR

30

-

-

dB

 

Spectrum Bandwidth(-20dB)

σ

-

-

1

nm

 

Extinction Ratio

ER

3.5

 

-

dB

Note (2)

Output Eye Mask

Compliant with FC_PI_4 REV 7.0

 

Note (2)

Receiver

Input Optical Wavelength

λIN

1260

1270

1280

nm

 

Receiver Sensitivity in average

PIN

-

-

-15

dBm

Note (1)

Input Saturation Power (Overload)

PSAT

0.5

-

-

dBm

Note (1)

LOS -Assert Power

PA

-30

-

-

dBm

 

LOS -Deassert Power

PD

-

-

-17

dBm

 

LOS -Hysteresis

PHys

0.5

-

5

dB

 

 

Note:
  1. The optical power is launched into SMF
  2. Measured with RPBS 2 31-1 test pattern @10.3125Gbs
  3. Measured with RPBS 2 31-1 test pattern @10.3125Gbs BER=<10 -12

 

  1. Electrical Interface Characteristics

Parameter

Symbol

Min.

Typ.

Max.

Unit

Note

Total power supply current

Icc

-

300

450

mA

 

Transmitter

Differential Data Input Voltage

VDT

180

-

700

mVp-p

 

Differential line input Impedance

RIN

85

100

115

Ohm

 

Transmitter Fault Output-High

VFaultH

2.4

-

Vcc

V

 

Transmitter Fault Output-Low

VFaultL

-0.3

-

0.8

V

 

Transmitter Disable Voltage- High

VDisH

2

-

Vcc+0.3

V

 

Transmitter Disable Voltage- low

VDisL

-0.3

-

0.8

V

 

Receiver

Differential Data Output Voltage

VDR

300

-

850

mVp-p

 

Differential line Output Impedance

ROUT

80

100

120

Ohm

 

Receiver LOS Pull up Resistor

RLOS

4.7

-

10

KOhm

 

Data Output Rise/Fall time

tr/tf

 

-

38

ps

 

LOS Output Voltage-High

VLOSH

2

-

Vcc

V

 

LOS Output Voltage-Low

VLOSL

-0.3

-

0.4

V

 

  1. Pin Description

 

Diagram of Host Board Connector Block Pin Numbers and Name

 

Pin

Symbol

Name/Description

Ref.

1

VEET

Transmitter Ground (Common with Receiver Ground)

1

2

TFAULT

Transmitter Fault.

2

3

TDIS

Transmitter Disable. Laser output disabled on high or open.

3

4

SDA

2-wire Serial Interface Data Line

4

5

SCL

2-wire Serial Interface Clock Line

4

6

MOD_ABS

Module Absent. Grounded within the module

4

7

RS0

Rate Select 0

5

8

LOS

Loss of Signal indication. Logic 0 indicates normal operation.

6

9

RS1

No connection required

1

10

VEER

Receiver Ground (Common with Transmitter Ground)

1

11

VEER

Receiver Ground (Common with Transmitter Ground)

1

12

RD-

Receiver Inverted DATA out. AC Coupled

 

13

RD+

Receiver Non-inverted DATA out. AC Coupled

 

14

VEER

Receiver Ground (Common with Transmitter Ground)

1

15

VCCR

Receiver Power Supply

 

16

VCCT

Transmitter Power Supply

 

17

VEET

Transmitter Ground (Common with Receiver Ground)

1

18

TD+

Transmitter Non-Inverted DATA in. AC Coupled.

 

19

TD-

Transmitter Inverted DATA in. AC Coupled.

 

20

VEET

Transmitter Ground (Common with Receiver Ground)

1

Notes:

  1. Circuit ground is internally isolated from chassis ground.
  2. TFAULTis an open collector/drain output, which should be pulled up with a 4.7k – 10k Ohms resistor on the host board if intended for use. Pull up voltage should be between 2.0V to Vcc + 0.3V.A high output indicates a transmitter fault caused by either the TX bias current or the TX output power exceeding the preset alarm thresholds. A low output indicates normal operation. In the low state, the output is pulled to <0.8V.
  3. Laser output disabled on TDIS>2.0V or open, enabled on TDIS<0.8V.
  4. Should be pulled up with 4.7kΩ- 10kΩ host board to a voltage between 2.0V and 3.6V. MOD_ABS pulls line low to indicate module is plugged in.
  5. Internally pulled down per SFF-8431 Rev 4.1.
  6. LOS is open collector output. It should be pulled up with 4.7kΩ – 10kΩ on host board to a voltage between 2.0V and 3.6V.      Logic 0 indicates normal operation; logic 1 indicates loss of signal.

 

  1. Recommended Interface Circuit

 

  1. Outline Dimensions

Appendix A. Document Revision

Version No.

Date

Description

1.0

2010-09-01

Preliminary datasheet

2.0

2011-09-10

Update format and company’s logo

E-mail: sales@sopto.com

Web : http://www.sopto.com